Highlights

ISCAR introduces a new LOGIQ3CHAM drill family which raises drilling performance levels to new heights. This family was designed by utilizing highly advanced technologies, based on ISCAR’s successful SUMOCHAM drill families.

The diameter range is .472 to 1.020” diameters, with drilling depth to diameter ratios of 1.5XD, 3XD and 5XD.
The new D3N drills can increase productivity by up to 50%, maintaining the excellent performance of the SUMOCHAM drills.

LOGIQ3CHAM applies the user-friendly drilling system for easy handling in accordance with the company motto of “No Setup Time”.





Features

H3P Drilling Heads

• Available in the drilling range of .472-1.020” diameters with .004 increments
• Single type geometry suitable for both ISO P and ISO K materials
• H3P drilling heads are made of IC908 TiAlN PVD nano layer coating grade, for prolonged and predictable tool life
• Unique wavy and honed cutting edges enable best chip form and easy chip evacuation process
  
• Patented concave cutting edges enable smooth penetration, excellent centering and stable drilling process
  
• Patent pending robust and precise chisel point and gash angle to withstand high cutting forces
• 15° corner chamfer increases wear resistance and strengthens the cutting corner
• Dovetail clamping prevents the head from being extracted from the pocket during retraction

D3N Drilling Holder

• Available in 1.5, 3 and 5 drilling depth to diameter ratios according to the list
• 3 variable and polished flute surfaces provide a smooth and easy chip evacuation process
• Variable flute angle design provides durable tool structure to withstand high axial forces
• Helical margin prevents chip adhesion between the body and the hole during machining
• Internal coolant channels supply efficient cooling and lubrication during the drilling process
• Tool body made from high grade of steel with superior hardness for high wear resistance
• Drilling head pocket designed to withstand high machining conditions, allowing easy and fast indexing

Enlarged flute volume for easy chip evacuation

• Optimized chip evacuation
• Strengthens the tool (especially during exit with high feed)

Pocket features

• Durable structure avoids plastic deformation and ensures a high number of drilling head indexing, up to 50 replacements
• Radial stoppers secure the drilling head and ensure a reliable drilling process in high feed machining environment
• Large face contact surface spreads out the pressure during the machining process
• 3 conical contact surfaces clamp the head inside the pocket to provide a precise and stable drilling process
• Close structure pocket is designed to increase heat resistance, which prolongs pocket tool life in difficult conditions

Patented pocket design


Case Study
TOOL 1: LOGIQ3CHAM (3 FLUTES - EXCHANGABLE HEAD)
TOOL 2: COMPETITOR A (3 FLUTES - EXCHANGABLE HEAD)
TOOL 3: COMPETITOR B (3 FLUTES – SOLID CARBIDE DRILL)
TOOL 4: COMPETITOR C (3 FLUTES – SOLID CARBIDE DRILL)

Material: AISI 4340 24-29 HRc


Performance

	Actual Diameter (inch))	Avg. Top Diameter (inch)	Avg. Bottom Diameter (inch)	Avg. Cone Value (inch)	Avg. Roughness (Ra)	Avg. Hole Roundness (inch)
LOGIQ3CHAM	.63012	.63099	.63087	.00020	.05123	.00012
COMPETITOR A	.63012	.63119	.63103	.00016	.08217	.00012
COMPETITOR B	.62957	.64619	.64560	.00052	.08134	.00036
COMPETITOR C	.63063	.63063	.63060	.00016	.06528	.00016

Note: the indicated above values are an average of all the cutting conditions applied below.


Diameter: .630"
Material: AISI 4340 24-29HRC *the LOGIQ3CHAM chip shapes were uniform and easy to evacuate in every cutting condition tested.

Tool Life
AISI4340
Vc=295sfm, f=.02008ipr



Material: ASTM A51670 147-190HB

	Actual Diameter (inch))	Avg. Top Diameter (inch)	Avg. Bottom Diameter (inch)	Avg. Cone Value (inch)	Avg. Roughness (Ra)	Avg. Hole Roundness (inch)
LOGIQ3CHAM	.63012	.63063	.63079	.00036	.10682	.00012
COMPETITOR A	.63012	.63099	.63079	.00040	.19670	.00036
COMPETITOR B	.62957	.63249	.63272	.00150	.17166	.00044
COMPETITOR C	.63063	.63071	.63119	.00044	.18733	.00036

Note: the indicated above values are an average of all the cutting conditions applied below.


Diameter: .630"
Material: ATSM A51670 147-190HB *the LOGIQ3CHAM chip shapes were uniform and easy to evacuate in every cutting condition tested.

Tool Life
ASTM A51670
Vc=360sfm, f= .01890ipr


Material: GGG 50 170-240HB

	Actual Diameter (inch))	Avg. Top Diameter (inch)	Avg. Bottom Diameter (inch)	Avg. Cone Value (inch)	Avg. Roughness (Ra)	Avg. Hole Roundness (inch)
LOGIQ3CHAM	.63012	.63020	.63024	.00016	.04800	.00008
COMPETITOR A	.63012	.63087	.63087	.00005	.06926	.00008
COMPETITOR B	.62957	.62977	.62977	.00005	.06930	.00024
COMPETITOR C	.63063	.63087	.63083	.00044	.06378	.00016

Note: the indicated above values are an average of all the cutting conditions applied in the test.


Tool Life
GGG 50
Vc=393 sfm, f=.02757 ipr


SYSTEM 3R (material: SAE 4340)

Vc=295 sfm
f=.01182 ipr

Identifier	Actual Roundness
Roundness (section cut in .11812”)	.00041
Roundness (section cut in .94489”)	.00028
Roundness (section cut in 1.77166”)	.00039

Vc=295 sfm
f=.02363 ipr

Identifier	Actual Roundness
Roundness (section cut in .11812”)	.00078
Roundness (section cut in .94489”)	.00098
Roundness (section cut in 1.77166”)	.00056

Designations


Tool


Head



General Recommendations:

• Dry drilling should not be performed under any circumstances
• Semi-synthetic or emulsion lubricants are recommended to be used for extended tool life
• It is essential to use internal coolant in all LOGIQ3CHAM applications
• In cases of low coolant pressure or when used in a stationary application, adding an external coolant can improve tool life
• When only external coolant can be applied, it is recommended to drill to a maximum depth of 2xD
• An optional plug with internal thread for coolant connection can be used on stationary machines. It can be pressed into the back-end hole of the drill

Shank Diameter	Plug	Internal Thread
.472	DL-12	G 1/16
.630	DL-16	G 1/16
.750	DL-20	G 1/8
1.000	DL-25	G 1/8

Following are the recommended ranges for coolant flow rate and pressure for each drill diameter
Drill Diameter (inch)

• For optimal performance, it is recommended to adjust runout of outer points and chisel with a maximum of .00079” exceeded runout will have influence on drill performance, tool life and hole quality.
• LOGIQ3CHAM drills can be used either on milling centers or lathe machines
• LOGIQ3CHAM drills can be used on sloped surfaces up to 12°. When drilling sloped surfaces of up to 12°, reduce feed rate by 30-50% during penetration up to 5 mm depth; or use a spot or pre-hole drill to avoid drill deviation or poor drill performance
• Interrupted cut has a direct influence on hole accuracy, quality and tool life

PreHole Adjustment



Dedicated LOGIQ3CHAM drill head key





(1) Cutting diameter minimum
• Do not mount smaller drilling heads other than the specified range of the drill body
(2) Cutting diameter maximum
(3) Seat size code




(1) Cutting diameter minimum
• Do not mount smaller drilling heads other than the specified range of the drill body
(2) Cutting diameter maximum
(3) Seat size code




(1) Cutting diameter minimum
• Do not mount smaller drilling heads other than the specified range of the drill body
(2) Cutting diameter maximum
(3) Seat size code




(1) Cutting diameter minimum
• Do not mount smaller drilling heads other than the specified range of the drill body
(2) Cutting diameter maximum
(3) Seat size code




(1) Cutting diameter minimum
• Do not mount smaller drilling heads other than the specified range of the drill body
(2) Cutting diameter maximum
(3) Seat size code




(1) Cutting diameter minimum
• Do not mount smaller drilling heads other than the specified range of the drill body
(2) Cutting diameter maximum
(3) Seat size code




(1) LPR tolerance ±.002”
(2) Seat size code
(3) PL tolerance ±.0039”




Material Groups

Recommended Machining Conditions


The NPA 013 inch -2019's pdf file: View (PDF) or Download (ZIP)