Highlights

ISCAR is expanding the advantageous SPINJET family with the introduction of the HPC line of compact, high-speed spindles for small diameter tools, driven by the coolant supply system of the machine tool.

The main feature of HPC, which sets it apart from other compact spindles in the SPINJET family, is its coolant pressure operating range. The new spindles are powered by the coolant supply at high pressure, (up to 1015 PSI).

The new HPC design enables application of the SPINJET technology to machine tools with high pressure coolant (HPC) flow, and with limited rotational velocity. In addition, it is also able to utilize the increased flow of HPC to provide higher power, making it suitable for increased-load machining operations compared to other SPINJET models.

General Data

Table 1. – General operating parameters

THE NEED: High Pressure + High Speed



SPINJET-HPC LINE SPINDLES – Special Features





SPINJET-HPC ER32 LINE - Adaptation Options




SPINJET-HPC LINE Spindle – Tool Holding & Mounting
Required:
Pull stud with coolant- through hole




Keeping the main spindle stationary
When the HPC Spindle is mounted on the machine, the CNC machine spindle should be stationary, except for tool checks.

To avoid CNC machine spindle rotation during the HPC Spindle operation, use the correct M code to lock spindle orientation, e.g. “M19” code locks the spindle in a defined angle position.

Machine tool requirements for using SPINJET-HPC LINE:

1. Coolant flow through the machine spindle
2. Minimum coolant pressure at main machine spindle outlet: 580 PSI
3. Maximum coolant pressure at main machine spindle outlet: 1015 PSI
4. 4.22-5.81 gallon/min
5. Use with water-based emulsion or cutting oil; viscosity up to 20(cP)
6. Minimum coolant filtration level: 100 μm
7. Active mist collector
8. With emulsion coolant, use an anti-foaming agent additive to prevent foaming
9. With oil coolant, high pressure increases the amount of oil fumes:
   1. Use appropriate means of fire protection and extinguishant
   2. Use anti-dissolution additive suitable for oil

SPINJET-HPC LINE Spindle - Tool Installation
First assemble the ER 11 collet and tool.

1. Insert nut for tightening. Align flat sides of the shaft with the positioning slot on the spindle cover.
2. Position shaft lock flat key over the nut. Black dot fits into the positioning slot underneath.
3. Slide shaft lock flat key to the left to secure it in place.
4. Insert ER11 wrench into the grooves on the nut.
5. Turn ER11 wrench clockwise to tighten.

To remove the tool

1. Slide the shaft lock flat key to the right to unlock.
2. Insert the wrench and turn counter-clockwise to loosen the nut (this may take a few turns).
3. Keep the shaft lock in the secure position if you wish to insert a new tool.

NOTE: ISCAR’s solid carbide endmills, threading endmills and drills are recommended for use on the new HPC high speed spindles.

Operating Tips

1. When operating the SPINJET-HPC LINE spindles, monitoring rotational speed is critical. A correctly set rotational speed ensures optimal machining conditions and avoids damaging the spindle.
   
2. Cutting speed depends on workpiece material and its hardness, the shape of a machined surface, a machining strategy and cutting tool geometry. Refer to cutting tool manufacturer’s documentation.
   
3. Dramatic fluctuations of the rotational speed (rpm) operation can indicate problems such as an inadequate coolant pressure or a broken cutting tool.

Using Precision ER11 Collets
When using ER11 spring collets, it is recommended to use only high quality precise collets that are engineered for maximum accuracy and tool life.

Max. collet runout (TIR) - .0002”


To maximize SPINJET-HPC LINE spindle tool life, we recommend following the “10% rule”:
The working rotational speed (rpm) should drop by up to 10% of the rotational speed (rpm), which is registered at ‘idle speed’.


Keeping this rule ensures reducing axial and radial load on the internal mechanism.

To register idle rotational speed:

1. Install the SPINJET-HPC LINE spindle carrying a cutting tool into the machine.
2. Start spindle rotation by turning on the fluid supply at required pressure and find the idle RPM speed by reading the display monitor of the spindle.

SPINJET-HPC LINE Spindle Operating Guidelines
Cutting Conditions

1. Monitoring RPMs during the SPINJET-HPC LINE spindle operation is critical to ensure optimum machining conditions and to avoid damage.
2. Cutting speed may be influenced by material hardness, work piece topography and /or cutting tool geometry.
3. Dramatic RPM fluctuations during the SPINJET-HPC LINE spindle operation may indicate insufficient coolant pressure or a broken cutting tool.

SPINJET-HPC LINE Spindle Storage
The HPC is free from periodic maintenance, however before storage it is recommended to:

• Clean the HPC by air blowing for 10-15 seconds
• Max. air pressure for cleaning: (30 psi) DO NOT EXCEED 60,000 RPM
• Disconnect the HPC from the display device
• Place the HPC back in its case

• Coolant pressure 40-70 bar and flow rate 16-22 l/min
• RPM range 35,000-50,000 RPM
• The spindle provides only external strong coolant jet around the tool

* Optional, should be ordered separately

• Coolant pressure 40-70 bar and flow rate 16-22 l/min
• RPM range 35,000-50,000 RPM
• The spindle provides only external strong coolant jet around the tool

* Optional, should be ordered separately

• Coolant pressure 40-70 bar and flow rate 16-22 l/min
• RPM range 35,000-50,000 RPM
• The spindle provides only external strong coolant jet around the tool

* Optional, should be ordered separately

• Coolant pressure 40-70 bar and flow rate 16-22 l/min
• RPM range 35,000-50,000 RPM
• The spindle provides only external strong coolant jet around the tool

* Optional, should be ordered separately

• Coolant pressure 40-70 bar and flow rate 16-22 l/min
• RPM range 35,000-50,000 RPM
• The spindle provides only external strong coolant jet around the tool

* Optional, should be ordered separately


Activating Spindle Warranty

Registration:
Each IMC office / dealer will get a dedicated “dash board” for their SPINJET product line (similar to My Matrix) with a full view of their customers and product history, providing a fast response to inquiries, plus top quality product service and repairs.

The product management interface includes:

1. Number of units
2. Serial numbers
3. To whom the product was sold
4. Sale date
5. Warranty (active / not active)
6. Service history

Registration for Customers:
When the product is officially registered, it not only activates the warranty but also entitles the end user to receive many important product support features:

• Product ATP
• Online Training & Documentation
• Product Management Interface
• Help & Technical Support Services

The warranty can be activated easily either by registering online at reg.colibri-jet.com or by scanning the QR code.




The NPA47-2018's pdf file (includes Installation and Operating Guides): View (PDF) or Download (ZIP)